{"product_id":"gannet-pro-motor-cw","title":"Gannet Pro Motor CW","description":"\u003ch2\u003eGenuine Clockwise (CW) Replacement Motor for the Gannet Pro Fishing Drone\u003c\/h2\u003e\n\u003cp\u003eThe Gannet Pro Motor CW is the genuine replacement clockwise-rotation motor for the \u003cstrong\u003eGannet Pro\u003c\/strong\u003e heavy-lift waterproof fishing drone. Clockwise (CW) motors are used in the front-right and rear-left positions on a standard quadcopter layout. Replacing a worn or damaged motor with a genuine Gannet part ensures the correct KV rating, torque curve, and mechanical dimensions are maintained—preserving the Gannet Pro's heavy-lift performance, waterproofing, and flight characteristic balance.\u003c\/p\u003e\n\n\u003ch2\u003eCW vs. CCW: Which Motor Do You Need?\u003c\/h2\u003e\n\u003cp\u003eQuadcopters like the Gannet Pro use two pairs of counter-rotating motors to balance torque and maintain stable flight:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClockwise (CW) motors — this listing:\u003c\/strong\u003e Front-right and rear-left positions. CW motors spin in the clockwise direction when viewed from above.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e\u003ca href=\"\/products\/gannet-pro-motor-ccw\" title=\"Gannet Pro Motor CCW\"\u003eCounter-clockwise (CCW) motors\u003c\/a\u003e:\u003c\/strong\u003e Front-left and rear-right positions. If you're unsure which motor position has failed, check the drone's motor shaft thread direction—CW motors typically use CCW-threaded prop nuts (tighten counter-clockwise), and CCW motors use CW-threaded prop nuts.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eTo identify a failed CW motor:\u003c\/strong\u003e Spin each motor shaft slowly by hand with power off—a failed motor will feel rough, grinding, or will have significantly more resistance than its pair. Video the drone from above during a brief hover on level ground and observe if one propeller is spinning slower or erratically.\u003c\/p\u003e\n\n\u003ch2\u003eWhy Use Genuine Gannet Replacement Motors?\u003c\/h2\u003e\n\u003cp\u003eThe Gannet Pro's heavy-lift fishing application places motors under sustained high-load conditions—carrying 2–3+ kg baits at range over salt water. Genuine Gannet Pro motors are:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eRated for the Gannet Pro's power system:\u003c\/strong\u003e The correct KV rating and winding resistance ensures the ESC and battery work within their designed parameters—preventing overheating under sustained load\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWaterproof-compatible construction:\u003c\/strong\u003e Designed to operate within the Gannet Pro's waterproof airframe; third-party motors may not meet the ingress protection requirements for surf launches and water exposure\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBalanced and flight-tested:\u003c\/strong\u003e Genuine motors maintain the prop-to-motor resonance balance that contributes to stable, vibration-free heavy-payload flight\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eKey Features\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClockwise (CW) rotation:\u003c\/strong\u003e Correct for front-right and rear-left motor positions on the Gannet Pro\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHeavy-lift motor design:\u003c\/strong\u003e High-torque motor wound for the Gannet Pro's power system and heavy-payload flight demands\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWaterproof construction:\u003c\/strong\u003e Sealed windings and corrosion-resistant materials for saltwater fishing drone operations\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIntegrated cooling design:\u003c\/strong\u003e Motor housing geometry promotes airflow during prolonged hover and sustained-payload flight\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGenuine Gannet replacement part:\u003c\/strong\u003e OEM component—correct dimensions, mounting bolt pattern, and shaft thread specification for the Gannet Pro airframe\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eWhen to Replace Your Gannet Pro Motor\u003c\/h2\u003e\n\u003cp\u003eReplace CW or CCW motors immediately if any of the following are observed:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eGrinding or rough rotation:\u003c\/strong\u003e Spin the shaft by hand—it should rotate freely and smoothly with no rough spots (indicates bearing failure)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eExcessive vibration during hover:\u003c\/strong\u003e Single-motor bearing wear causes vibration that worsens rapidly under load and can lead to in-flight failure\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePhysical damage:\u003c\/strong\u003e Bent shaft, cracked motor can, or damaged stator windings from a hard landing or prop strike\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCorrosion on windings:\u003c\/strong\u003e Visible salt corrosion inside the motor housing after repeated saltwater exposure without adequate rinsing\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMotor running hot:\u003c\/strong\u003e A motor that is significantly hotter than its pair after a flight may be failing internally\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eSaltwater Motor Care: Extend Motor Service Life\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eRinse with fresh water after every saltwater session:\u003c\/strong\u003e Allow the drone to hover briefly over land to spin out standing water, then rinse the motor housings gently with a fresh-water spray from above\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDry before storage:\u003c\/strong\u003e Do not store the drone with wet motors—moisture accelerates bearing corrosion and winding degradation\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInspect bearings quarterly:\u003c\/strong\u003e Spin each motor shaft by hand every 3–4 months; replace at the first sign of roughness, clicking, or resistance\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAvoid salt build-up on windings:\u003c\/strong\u003e Salt crystallising on motor windings over time reduces efficiency and accelerates corrosion\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eTechnical Specifications\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eRotation:\u003c\/strong\u003e Clockwise (CW)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatibility:\u003c\/strong\u003e Gannet Pro fishing drone\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eApplication:\u003c\/strong\u003e Heavy-lift waterproof drone propulsion\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eType:\u003c\/strong\u003e Genuine Gannet OEM replacement part\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eRelated Gannet Pro Parts \u0026amp; Accessories\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e\u003ca href=\"\/products\/gannet-pro-motor-ccw\" title=\"Gannet Pro Motor CCW\"\u003eGannet Pro Motor CCW\u003c\/a\u003e\u003c\/strong\u003e — counter-clockwise replacement motor for front-left and rear-right positions\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e\u003ca href=\"\/collections\/fishing-drones\" title=\"Fishing drones\"\u003eFishing drones\u003c\/a\u003e\u003c\/strong\u003e — Gannet Pro, SwellPro, and SkyAngler platforms for Australian offshore bait delivery\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e\u003ca href=\"\/collections\/bait-release-systems\" title=\"Bait release systems\"\u003eBait release systems\u003c\/a\u003e\u003c\/strong\u003e — payload releases compatible with the Gannet Pro\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eDelivery \u0026amp; Support\u003c\/h2\u003e\n\u003cp\u003eAustralia-wide shipping. Free delivery on orders over $99. Need help identifying which motor position has failed on your Gannet Pro, or advice on motor inspection and maintenance? Contact the DroneFisher team.\u003c\/p\u003e","brand":"Gannet","offers":[{"title":"Default Title","offer_id":49645488144640,"sku":"DF-GAN-0044-01","price":89.99,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0854\/9063\/0912\/files\/dc6e75d28ace3a5353069b52e49494d0.jpg?v=1788635946","url":"https:\/\/www.dronefisher.com.au\/products\/gannet-pro-motor-cw","provider":"Drone Fisher","version":"1.0","type":"link"}